Dana 44 ball joints

4x4 & Off-road Forum Archives

Moderator: Doug Comer

Post Reply
James72
Preferred User
Preferred User
Posts: 310
Joined: Tue Oct 09, 2007 10:37 pm
Location: Vernon BC

Dana 44 ball joints

Post by James72 »

I popped the ball joints out of my dana 44 today and it looks like the top one is either adjustable or had some sort of sleeve threaded in it, if it's adjustable dose anyone know the procedure? Also how is the top ball joint retained in the knuckle, it dosen't look like I can press it either way cause there is a step on both sides, it's pretty rusted though I may be missing something. Thanks, James

Image

Image
'05 Mustang GT
'72 crew 4x4
'07 KTM 450 xcw
2006 F350 CC Diesel 4x4 Lariat
James72
Preferred User
Preferred User
Posts: 310
Joined: Tue Oct 09, 2007 10:37 pm
Location: Vernon BC

re: Dana 44 ball joints

Post by James72 »

I got the new ball joints in, they were just built up with rust so it only looked like it had a step, and apparently the upper threaded bushing is for preloading the ball joints now all I need is a special socket and a torque spec. :roll:


James
'05 Mustang GT
'72 crew 4x4
'07 KTM 450 xcw
2006 F350 CC Diesel 4x4 Lariat
User avatar
Wes
Blue Oval Fan
Blue Oval Fan
Posts: 732
Joined: Fri Oct 21, 2005 6:04 pm
Location: California, Southern& Lake Havasu Az

Post by Wes »

take that old sleeve out you should get new ones w/ new BJ's . Thread the new sleeve in part way install the knuckle w/ new bj's tighten down the lower I believe torque is @ 80 ft pnds. Now you will need the a spanner socket to fit the sleeve torque the sleeve down to 50 ft pnds install the upper ball joint lock nut your done.
Wes

http://www.fordification.com/galleries/ ... ?cat=10402
67 F250 High boy
69 Bronco

If you can't see fit to stand behind Our Troops...Please stand in front of them :)
James72
Preferred User
Preferred User
Posts: 310
Joined: Tue Oct 09, 2007 10:37 pm
Location: Vernon BC

re: Dana 44 ball joints

Post by James72 »

yep, that was exactly right, it went together pretty easy

now the next problem, I put my spindle in the parts washer and it came out without and needles left in the bearing for the drive axle.

Nobody can find them and Ford says to measure it, anyone have one? Id like just a part number then I'll just go to the bearing store and skip Ford, save some $$$.



James
'05 Mustang GT
'72 crew 4x4
'07 KTM 450 xcw
2006 F350 CC Diesel 4x4 Lariat
fordguy_78
New Member
New Member
Posts: 108
Joined: Wed May 25, 2005 1:12 am
Location: Washington, Spokane
Contact:

re: Dana 44 ball joints

Post by fordguy_78 »

I would just go to http://broncograveyard.com/bronco/i-221 ... ir_kit.htm that should be what you need
Phill
78 Mustang
67 F250ish
2010 F250 Harley Davidson
James72
Preferred User
Preferred User
Posts: 310
Joined: Tue Oct 09, 2007 10:37 pm
Location: Vernon BC

re: Dana 44 ball joints

Post by James72 »

ok now I have the bearing in, every thing set up and....
When I unlock the hub it gets real tight towards the end, then when I unlock it the dog clutch wont engage right away, If I tap it with a hammer it locks in right away, almost like the spring is weak. It also feels like the knob is pushing the hub in too far when releasing the dog clutch.
This is an axle I've never used so I don't know if it was like this before.
Anyone had a similar problem?

And thanks fordguy_78 that is exactly what I needed :thup:


James
'05 Mustang GT
'72 crew 4x4
'07 KTM 450 xcw
2006 F350 CC Diesel 4x4 Lariat
Post Reply