The FORDification.com Forums

by **4x4x4crewcab** on Sat Jan 06, 2007 12:54 am

I just opened my new Classic Trucks Magazine and besides the fact that it is a SUPER GREAT Ford bumpside issue there is a nice plug for Keith on p. 43. Its the back of someone(maybe our own buckinthebowtie) working on a bump wearing a Fordification T-shirt.
Let me be the first to internet shake the hand of the man (Keith) :thup:

And thanks Grant for the plug

by **FORDification** on Sat Jan 06, 2007 1:44 am

If you got yours already, then I'm guessing I'll get mine tomorrow. Looking forward to seeing it!

Thanks Mark! :thup:

by **wt4speed#2** on Sat Jan 06, 2007 3:06 am

Yea I got mine today as well was gonna post and never got to it . Great progress Grant. As Freddy Prinze would say to the "Man" "Looking Good"

Tony B

by **rjewkes** on Sat Jan 06, 2007 3:12 am

I wonder if mine will be the same one or if it will be the next one? I oprdered just before Christmas.

by **69F110** on Sat Jan 06, 2007 5:00 am

Awesome!

by **71 LONG BED** on Sat Jan 06, 2007 9:35 am

I'm all the way on the east coast. I allways get mine last.

Can't wait to see it though!

by **ExplorerNC** on Sat Jan 06, 2007 9:38 am

I wl have to pick up a copy. What's on the cover of the new one?

by **FORDification** on Sat Jan 06, 2007 1:41 pm

I got mine this morning...and a bumpside's on the cover, even! It's the Fatman's Fabrications shop truck, along with a full 5-page feature of it inside, in addition to Grant's 6-page article of the Fatman's IFS installation on his '68. :thup:

...and yes, there's a very good picture of Grant wearing his FORDification t-shirt. :thup:

I've got a few questions for him regarding the Fatman's kit, but I'll start a new thread later on this.

by **CACWBY** on Sat Jan 06, 2007 7:25 pm

RE: Grants' article. After reading the article on doing IFS - I'm thinking I might have to buy an Art Morrison Chassis. I could not do this myself, so add shop labor to the materials cost (and the rear end and as well), and unless you can DIY, the whole new chassis starts looking a little less expensive.

by **FORDification** on Sun Jan 07, 2007 7:22 am

For those of you who aren't subscribers and will be looking for this issue at your local newsstand, here's a quick scan of the cover:

...and here's the afore-mentioned shot of Grant working on the Fatman IFS kit on his '68:

by **OldBlue67** on Sun Jan 07, 2007 2:21 pm

Awesome shot! hehe Good looking truck on the front too. I'm going to have to pick up this issue!

by **mljjones67** on Sun Jan 07, 2007 5:32 pm

I wear my shirt like that all the time especially to car shows and when I talk to people about selling there trucks

by **Tallboy** on Sun Jan 07, 2007 7:44 pm

Sweet!

Gonna have to go check out the store and pick up a copy.

by **rjewkes** on Sun Jan 07, 2007 9:10 pm

? I thought the Twin I's where IFS in a sort of old fashioned way?

for instance if you park your 67-96 F100/f150-f350 2 wd truck in a spot with a pothole say 1-6" deep under neath the drivers front tire

for the most part only the I-Beam on that side would flex enough to make the truck still sit even.